|
|
 |
|
Red & White Reflective Tape/
slightly defective/multiple patterns
|
1/2 PRICE
|
Department Of Transportation
Approved
2" Wide X 18" Long Red & White Reflective Tape
sections (also known as conspicuity
tape)
Special purchase/slightly defective/
multiple patterns:
Some 18" sections have a slight
vertical mark on it, that you can't see from a few
feet away. They do not make
any difference in the way the product
performs. Actual patterns may vary.
Peel & Stick. Permanent. Apply to the sides and
back of your trailer for higher visibility. Sold
in one 11" red and one 7" white
section= 18 inches.
We custom cut in multiple
lengths of 18 inches, and your order will
arrive all in one continuous piece.
Standard shipping fees apply--NON-RETURNABLE
|
|
2" Wide X 18" Long Red & White Reflective Tape/slightly
defective
|
|
|
|
|
Rapid
Hitch--the last ball mount you'll ever buy!:
SALE! |
 |
This is the well-known
Rapid Hitch, made with solid super alloy aluminum, made by
Anderson. 10,000 lb. GTW/ 1,500 lb. TW.
SALE! Until the end of June, 2010, get FREE
SHIPPING on all Rapid Hitches! (Call
in your order, or if
the website charges you, we'll refund the
shipping right back).
Each features a 2" and
a 2 5/16" steel ball, rated
at 10,000 lbs. and comes
standard with a non-locking stainless steel pin (pictured).
To operate, just pull the pin, adjust up or
down & slide the pin back in. The ball
mounts can be reversed to fit upwards for
added rise positions.
Consider upgrading &
protecting your investment with a LOCKING stainless
steel 2-pin set, keyed alike
(one receiver pin and 1 matching pin) for the
Rapid Hitch.
We do not take returns
on these items, because they usually
come back scratched. Everyone deserves a
new, unused product when ordering a Rapid
Hitch.
*Order carefully---these
ball mounts are NOT RETURNABLE!
The most common mistake is ordering a ball
mount that will scrape the ground when
driving over bumps or up & down steep roads,
because the vehicle doesn't provide enough
clearance.
|
|
Rapid Hitch, 5 1/4" Drop/Rise, w/ 2 Chrome Steel
Balls |
|
|
|
Rapid Hitch, 5 1/4" Drop/Rise, w/ 2 Stainless
Steel Balls |
|
|
|
Rapid Hitch, 10" Drop/Rise, w/ 2 Chrome Steel
Balls |
|
|
|
Rapid Hitch, 10" Drop/Rise, w/ 2 Stainless Steel |
|
|
|
Rapid Hitch, Keyed Alike Locking 2 Pin Set/Class
III & IV |
|
|
|
Rapid Hitch, Keyed Alike Locking 2 Pin Set/Class
V |
|
|
|
|
EXTRA Large
Round POLYURETHANE Door Stop-CLOSEOUT |
 |
EXTRA Large POLYURETHANE Door Stop
(These are the best we
can find, but no one is ordering them!!)
1" tall X 3 1/4" in diameter, clear
amber
color.
This is the toughest/hardest
door stop we can find! Installed on the body of the trailer
OR
installed in multiples on the bottom of trailer entry
ramps where they rest on the ground. Gives 1"
clearance under the ramp in order to
safely get your fingers under & lift it.
*Install with a
#14 X
1 1/2" sheet metal screw
& #14 X 1 1/14" washer through the pre-drilled hole in the center.
|
| |
EXTRA Large POLYURETHANE Door Stop/SALE |
|
|
|
|
White
Plastic RV Vent Trim-
not
needed |
|
We have 4
available |
These are plastic roof vent trim, in a
size we don't carry (perhaps they are for RV vents?)
The are rectangular, with rounded
corners, and the hole measurement would be approximately
10 1/4"L X 4 3/4"W. Trim is 1 1/2" Tall.
Standard shipping fees apply-NON-RETURNABLE |
|
White Plastic Vent Trim /
not needed |
|
|
|
|
Steel Two-Way Roof Vent/
slightly damaged |
These
are perfect:.JPG)
.JPG)
+++++++++++
Three
have had the handles bent like this:
|
Two-Way Roof Vent,
in Steel, powder-coated,
black
We have
upgraded our roof vents and now offer
you the best & safest roof
vent for equines on the market today! The 3 metal
blades that were a danger to animals are
now eliminated--much safer for your
animals, in case of impact. The
interior handle
with which to position the vent lid is fastened on much more
securely and it is easier to grasp.
It has a ergonomic grip -one squeeze of
the handle relieves the sealing force
for simple opening in either direction.
In addition, there is a full-size
neoprene gasket in the lid to prevent
leaks.
We
recommend installing the closed-cell
gasket made specifically for this roof
vent to prevent leaking. This gasket
also makes a great template for cutting a
perfect hole in the trailer roof. Dimensions: 7 3/4"
wide x 13 3/8" long
Hole Size:
6 1/4" wide x 11 3/4" long (oval shape)
(Gasket
& trim sold separately on Vents
page.)
+++++++++++++++++++++++++++++++++++
* NOTE: We are offering
at a reduced were delivered with one or
both of the 1/16" thick steel blades
that support the handle bent slightly.
If you have the ability to straighten
the blades, you can get these at
less than 1/2 price. NO RETURNS. |
|
Two-Way
Roof Vent, Steel
(powder-coated black)/ slightly damaged |
|
|
|
|
|
