Fasteners

 #8 Wood Screws And Washers

We use these zinc-coated steel wood screws to attach horse trailer pads to the inner sides of trailers that are lined in wood, especially the center dividers that may be only one sheet of plywood. Use in combination with a #8 washer. Can also be used for sheet metal.  Drill a hole to start if the trailer wall is over 18" gauge.  
Flat Head Wood Screw #8 X 1/2"

Product Name:
 
SKU:
Price (US$):

Flat Head Wood Screw #8 X 3/4"

Product Name:
 
SKU:
Price (US$):

#8 Washer, zinc

Product Name:
 
SKU:
Price (US$):

#8 Sheet Metal Screws & Washers

We use these zinc-coated steel self-drilling pan head screws to attach horse trailer pads to the inner sides of trailers that are lined in steel. Use in combination with a #8 washer.
Sheet Metal Screw, #8 X 1/2"

Product Name:
 
SKU:
Price (US$):

Sheet Metal Screw #8 X 3/4"

Product Name:
 
SKU:
Price (US$):

#8 Washer, zinc

Product Name:
 
SKU:
Price (US$):

# 10 Sheet Metal Screws
We use these zinc-coated steel pan head screws to attach most of our light weight hardware products such as positive door holders, small D-rings w/Bracket, and strap loops.  Some door holder receivers will use a #12 or #14 sheet metal screw for strength. 
Sheet Metal Screw #10 X 1" Pan Head, Phillips

Product Name:
 
SKU:
Price (US$):

#12 & #14  Sheet Metal Screws

We use these zinc-coated steel flat-head screws to securely attach products such as door holders, door holdbacks & door stops to steel horse trailers. Drill a hole to start if the trailer wall is over 18" gauge. 
Sheet Metal Screw, #12 X 1"

Product Name:
 
SKU:
Price (US$):

Sheet Metal Screw #14 X 1"

Product Name:
 
SKU:
Price (US$):

Sheet Metal Screw #14 X 1 1/2"

Product Name:
 
SKU:
Price (US$):

#10 Machine Screw & Jacknut

#10  Pan Head Machine Screw, in stainless steel. This is the anchor system we recommend using to secure the receivers for door stops and door holdbacks. The screw is stainless steel, and the jack nut is zinc/steel.  Drill a 3/8" hole , then tap the nut in. Place the part over the hole, & tighten the screw. It creates an anchor that can't be pulled out by yanking on the door.
Pan Head Machine Screw

Product Name:
 
SKU:
Price (US$):

Jack Nut, #10-24, Zinc

Product Name:
 
SKU:
Price (US$):

1/4" Machine Screw & Jack Nut

1/4" Oval Pan Head Machine Screw, in stainless steel (the size is equivalent to a #12 screw). This is the anchor system we recommend using to secure the Keyed Cam Latch System or receivers for door stops and other door holdbacks. The screw is stainless steel, and the jack nut is zinc/steel.  Drill a 7/16" hole , then tap the nut in. Place the part over the hole, & tighten the screw. It creates an anchor that can't be pulled out by yanking on the door.
Oval Pan Head Machine Screw, 1/4", stainless steel

Product Name:
 
SKU:
Price/ea (US$):

Jack Nut, #12 X 1/4", Zinc

Product Name:
 
SKU:
Price/ea (US$):

TEK Screws

Wafer TEK screws have a 1/2" wide flat head, so  that a washer is not needed. These are self-drilling, and are used to attach rubber mats or liners to the smooth interior of horse trailer walls. Depending on how thin the mat is and how thick the wall is, choose either 3/4" or 1 inch long screw
TEK Screw, # 10 X 3/4"

Product Name:
 
SKU:
Price (US$):

TEK Screw, # 10 X 1"

Product Name:
 
SKU:
Price (US$):

 1/4" Diameter TORX Floor Screws
Used when replacing wood floors in trailers. Drill hole through wood floorboard into metal floor supports, then install screw so that the screw head is flush with the floor. Black. 

*Use TORX hex drive tool for installation (available below).

1 1/2" Long X 1/4" Diameter TORX Floor Screw

Product Name:
 
SKU:
Price/ea. (US$):

2" Long X 1/4" Diameter TORX Floor Screws

Product Name:
 
SKU:
Price/ea. (US$):

2 1/2" Long X 1/4" Diameter TORX Floor Screws

Product Name:
 
SKU:
Price/ea. (US$):